[J1970M2]

Thanks so much for the response. Thanks to your feedback, I think I have a solution. I created a new Access Control profile and:

* Blocked all P2P traffic
* Blacklisted 192.168.1.0/24
* Added the device I want to block to the profile

I then joined the device to the Guest network and it cannot:

* Get to the pcWrt login page
* Browse any shares
* Get to other device LAN network pages

I think that will do it! Thank you. Apologies for not mentioning that I know the device name I want to block.

[J1970M2]

Hello,
Any suggestions? I tried disabling WireGuard, removing the 192.168.1.0/24 added to the WireGuard tunneling page, removed all checkmarks for Guest on the vLan page, but no matter what I try, a device on Guest has full access to my shard directories that are only shared on the LAN (no WAN access). I’m stumped.
Thanks

[J1970M2]

Hello,
I basically have two routers:

Router A has the Internet from my ISP – all devices on that router are within 192.168.1.xxx.
Router B (pcWrt) WAN port connects To Router A port and routes to devices that I want to have a 24/7 WireGuard connection – all devices on Router B are within 192.168.2.xxx.
Router B (pcWrt) can access devices on Router A with 192.168.1.0/24 added to the WireGuard tunneling page.

I want a Guest Wifi network on Router B (pcWrt) that CANNOT access anything other than an Internet connection. I created the Guest WiFi network, but a device on the Guest network can access a share on 19.1.68.1.xxx and I don’t want it to.

Thanks for your help.

[J1970M2]

Nevermind, I do get more than 20 gbps down.

[J1970M2]

Figured it out; click the ‘+’ icon on the Wireless page. All good now. Looks like Guest is limited to 20 gbps down?
Thanks!

[J1970M2]

Thank you!

[J1970M2]

Hello Support,
I don’t know if the router restarted when the power blipped. At the time I never thought to look. After work (8 hours), I performed a “What’s my IP address” check and the result was outside the VPN tunnel. I then looked at my WireGuard configuration on the router and it was supposedly active and “green led”. I stop/started the WireGuard tunnel and performed a “What’s my IP address” check and the result was now inside the VPN tunnel.
I know my VPN tunnel was active the night before, then after the early morning power blip it was not, and seemingly for the 8 hours I was at work.
Note: I have since updated the firmware from 2.7.6 to 2.7.8.
Thanks!

[J1970M2]

Update: Finally got v2.7.8 to work with access from my Channels DVR, Home Assistant server, etc. I had to disable Access Control > Profiles > Enforce Access Control and all is now working on v2.7.8.
Thanks again.

[J1970M2]

Update: Finally got v2.7.8 to work with access from my Channels DVR, Home Assistant server, etc. I had to disable Access Control > Profiles > Enforce Access Control and all is now working on v2.7.8.
Thanks again.

[J1970M2]

Hello Support,
I’m using a PW-AX1800 over WiFi.
Thanks!

[J1970M2]

I’m still having issues. Kills my Channels DVR streaming client/server connection. When I revert to 2.7.6, everything works again.

[J1970M2]

Still the same for me; 2.7.7 kills my internet connection (WireGuard – Windscribe), when I revert back to 2.7. 6 everything works again.

[J1970M2]

Hello,
PW-AX1800
Thanks

[J1970M2]

I just posted my experiences with v2.7.7, it killed my VPN connection. Rolled back to v2.7.6 and all is working again.

[J1970M2]

Thanks so much!

[Author]

Posts